Casio Collection W-753-1AVES bruksanvisning

Casio Collection W-753-1AVES
8.5 · 4
PDF bruksanvisning
 · 4 sider
Engelsk
bruksanvisningCasio Collection W-753-1AVES

Operation Guide 2926

1
MO0503-EB

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully and keep it on hand for later reference
when necessary.
Warning!
The longitude, lunitidal interval, Moon phase indicator, tide graph data, and solar
azimuth data that appear on the display of this watch are not intended for
navigation purposes. Always use proper instruments and resources to obtain data
for navigation purposes.
This watch is not an instrument for calculating low tide and high tide times. The
tide graph of this watch is intended to provide a reasonable approximation of tidal
movements only.
When engaging in mountain climbing or other activities in which losing your way
can create a dangerous or life-threatening situation, always be sure to use a
second compass to confirm direction readings.
CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any
claims by third parties that may arise through the use of this watch.

About This Manual

Button operations are indicated using the letters shown
in the illustration.
Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
(Light)

General Guide

The illustration below shows which buttons you need to press to navigate between
modes.
In any mode, press L to illuminate the display.
Moon / Tide Data Mode Countdown Timer Mode
Dual Time Mode
Timekeeping Mode
Alarm Mode
Stopwatch Mode
Press C.
Press B.
Bearing Mode
Press C.

Timekeeping

Use the Timekeeping Mode to set and view the current
time and date.
The tide graph shows tidal movements for the current
date in accordance with the current time as kept in the
Timekeeping Mode.
The Moon phase indicator shows the current Moon
phase in accordance with the current date as kept in the
Timekeeping Mode.
Important!
Moon phase, tide graph data, Bearing Mode solar
azimuth data, and Moon/Tide Data Mode data will not
be displayed properly unless the Timekeeping Mode
current date and time settings and Home Site data are
configured correctly. See “Home Site Data” for more
information.
Day of week
Month – Day
Hour : Minutes Seconds
PM
indicator
Tide graph
Moon phase indicator
To set the time and date
1.In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2.Press C to move the flashing in the sequence shown
below to select other settings.
Hour
Seconds
12/24-Hour
Format
Day Month
Year
Minutes
3. When the setting you want to change is flashing, use D and B to change it as
described below.
|
|
|
|
|
|
|
|
|
|
|
|
|
Year
To change this setting
Seconds
Hour, Minutes, Year,
Month, Day
12/24-Hour Format
Perform this button operation
Press D to reset to 00.
Use D (+) and B (–) to change the setting.
Press D to toggle between 12-hour (12H) and
24-hour (24H) timekeeping.
4. Press A twice to exit the setting screen.
The first press of A displays the GMT differential setting screen. Pressing A again
exits the setting screen.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Home Site Data
Tide graph data and Bearing Mode solar azimuth data will not be displayed properly
unless Home Site data (GMT differential, longitude, and lunitidal interval) is configured
correctly.
The GMT differential is the time difference of the time zone where the site is located
from Greenwich Mean Time.
Note that you must add one hour to the GMT differential for your time zone
whenever you change to Daylight Saving Time. Subtract one hour when you change
back to Standard Time.
The lunitidal interval is the time elapsing between the Moon’s transit over a meridian
and the next high tide at that meridian. See “Lunitidal Interval” for more information.
This watch displays lunitidal intervals in terms of hours and minutes.
The “Site/Lunitidal Interval Data List” provides GMT differential, longitude, and
lunitidal interval information around the world.
The following is the initial factory default Home Site data (Tokyo, Japan) when you
first purchase the watch and whenever you have the battery replaced. Change these
settings to match the area where you normally use the watch.
GMT differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,20 minutes)To configure Home Site data
1.In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2.Press A again to display the GMT differential setting
screen.
3.Press C to move the flashing in the sequence shown
below to select other settings.

Lunitidal Interval

Hours

Lunitidal Interval

Minutes

Longitude

GMT

Differential

4. When the setting you want to change is flashing, use D and B to change it as
described below.
GMT differential
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Setting
GMT Differential
Longitude
Lunitidal Interval
Hours, Minutes
Screen Button Operations
Use D (+) and B (–) to change the setting.
Yo u can specify a value in the range of –11.0
to +14.0, in 0.5-hour units.
Use D (+) and B (–) to change the setting.
Yo u can specify a value in the range of
179°W to 180°E, in 1-degree units.
Use D (+) and B (–) to change the setting.
5. Press A to exit the setting screen.

Bearing Mode

The Bearing Mode lets you determine approximate
directions using a displayed angle value that indicates the
angle to the sun (solar azimuth).
All of the operations in this section are performed in the
Bearing Mode, which you can enter from the
Timekeeping Mode by pressing B.
Important!
Before the watch can calculate the solar azimuth (the
angle of the sun in relation to your location) correctly, you
must first set the correct current time, current date, and
Home Site in the Timekeeping Mode. You must also
specify whether the sun traverses the sky to the north or
to the south of your current position.
Solar azimuth
Note that you cannot use the Bearing Mode to determine directions in the following
cases.
When the sun is not visibl
e
At nightWhen sun traverses the sky directly overhead or when you cannot determine if ittraverses to the north or southTo set the traverse direction of the sun
1.In the Bearing Mode, hold down A until N or S flashes
on the display. This indicates the setting screen.
2.Press D to toggle the setting between N (north) and S
(south).
3.Press A to exit the setting screen.
At this time the watch uses the traverse direction setting
you just configured and the Timekeeping Mode data to
calculate and display the solar azimuth.
|
|
|
|
|
|
|
|
|
|
|
|
|

Bruksanvisning

Se håndboken for Casio Collection W-753-1AVES her gratis. Denne håndboken er under kategorien Armbåndsur og har blitt vurdert av 4 personer med et gjennomsnitt på 8.5. Denne håndboken er tilgjengelig på følgende språk: Engelsk. Har du et spørsmål om Casio Collection W-753-1AVES eller trenger du hjelp? Still spørsmålet ditt her

Trenger du hjelp?

Har du spørsmål om Casio Collection W-753-1AVES og svaret står ikke i manualen? Still spørsmålet ditt her. Gi en klar og omfattende beskrivelse av problemet og spørsmålet ditt. Jo bedre problemet og spørsmålet beskrives, jo enklere vil det være for andre eiere av Casio Collection W-753-1AVES å kunne gi deg et godt svar.

Antall spørsmål: 0

Spesifikasjoner for Casio Collection W-753-1AVES

Nedenfor finner du produktspesifikasjonene og de manuelle spesifikasjonene til Casio Collection W-753-1AVES.

Generelt
Merke Casio
Modell Collection W-753-1AVES
Produkt Armbåndsurer
Språk Engelsk
Fyltype Brukermanual (PDF)

Vanlige spørsmål

Finner du ikke svaret på spørsmålet ditt i manualen? Du kan finne svaret på spørsmålet ditt i Vanlige spørsmål om Casio Collection W-753-1AVES under.

Finner du ikke spørsmålet ditt i listen? Still spørsmålet ditt her

Ingen resultater